Fuji frenic 5000g11 мануал

Instructions on maintenance, inspection, and replacement

• Wait a minimum of five minutes (30HP or less) or ten minutes (40HP or more) after power has been tumed

off (open) before starting inspection. (Also confirm that the charge lamp is off and that DC voltage between

terminals P (+) and N (-) do not exceed 25V.)

Electrical shock may result.

• Only authorized personnel should perform maintenance, inspection, and replacement operations.(Take off

metal jewelry such as watches and rings. Use insulated tools.)

Electric shock or injury may result.

Instructions on disposal

• Treat as industrial waste when disposing it.

Injury may result.

Other instructions

• Never modify the product.

Electric shock or injury may result.

Conformity to Low Voltage Directive in Europe

• The contact capacity of alarm output for any fault (30A, B, C) and relay signal output (Y5A, Y5C) is 0.5A at

48V DC.

• The ground terminal

Use a crimp terminal to connect a cable to the main circuit terminal or inverter ground terminal.

• Where RCD (Residual-current protective device) is used for protection in case of direct or indirect contact,

only RCD of type B is allowed on the supply side of this EE (Electric equipment).

Otherwise another protective measure shall be applied such as separation of the EE from the environment

by double or reinforced insulation or isolation of EE and supply system by the transformer.

• Use a single cable to connect the

terminals.)

• Use a molded-case circuit breaker (MCCB) and magnetic contactor (MC) that conform to EN or IEC

standards.

• Use the inverter under over-voltage category III conditions and maintain Pollution degree 2 or better as

specified in IEC664. To maintain Pollution degree 2 or more, install the inverter in the control panel (IP54

or higher level) having structure free from water, oil, carbon, dust, etc.

• For the input-output wiring of the inverter, use cable (diameter and type) as specified in Appendix C in

EN60204.

• To ensure safety, install an optional AC reactor, DC reactor, or external braking resistor as follows:

1) Install inside an IP4X cabinet or barrier if electrical parts are exposed.

2) Install inside an IP2X cabinet or barrier if electrical parts are not exposed.

• It is necessary to install the inverter in appropriate method using an appropriate RFI filter to conform to the

EMC directive. It is customer’s responsibility to check whether the equipment, the inverter is installed in,

conforms to EMC directive.

G should be connected to the ground.

G inverter ground terminal. (Do not use two or more inverter ground

WARNING

CAUTION

WARNING

CAUTION

Instruction Manual

FRENIC 5000G11S/P11S

High-Performance, Low-Noise Inverter

General-Purpose Industrial Machines Fans and Pumps

230V Series 230V Series

0.25HP/FRNF25G11S-2UX 7.5HP/FRN007P11S-2UX

to 125HP/FRN125G11S-2UX to 150HP/FRN150P11S-2UX

460V Series 460V Series

0.50HP/FRNF50G11S-4UX 7.5HP/FRN007P11S-4UX

to 600HP/FRN600G11S-4UX to 800HP/FRN800P11S-4UX

！

CAUTION

 Read all operating instructions before

installing, connecting (wiring),

operating, servicing, or inspecting the

inverter.

 Ensure that this instruction manual is

made available to the final user of the

inverter.

 Store this manual in a safe,

convenient location.

 The product is subject to change

without prior notice.

Fuji Electric FA Components & Systems Co., Ltd. INR-SI47-1206-E

Fuji Electric Corp of America

Instruction Manual

FRENIC 5000G11S/P11S

High-Performance, Low-Noise Inverter

General-Purpose Industrial Machines

Fans and Pumps

230V Series

230V Series

0.25HP/FRNF25G11S-2UX 7.5HP/FRN007P11S-2UX
to 125HP/FRN125G11S-2UX

to 150HP/FRN150P11S-2UX

460V Series

460V Series

0.50HP/FRNF50G11S-4UX 7.5HP/FRN007P11S-4UX
to 600HP/FRN600G11S-4UX

to 800HP/FRN800P11S-4UX

！

CAUTION

„

Read all operating instructions before

installing, connecting (wiring),
operating, servicing, or inspecting the
inverter.

„

Ensure that this instruction manual is

Store this manual in a safe,

The product is subject to change

Fuji Electric FA Components & Systems Co., Ltd.

INR-SI47-1206-E

Fuji Electric Corp of America