Godex rt200 руководство

• Page 1: User Manual

  RT200/RT230 BARCODE PRINTER USER MANUAL User Manual : RT200 series Version : Rev. 1.5 Issue Date : 2013.07.04 : 920-014311-00…

• Page 2: Table Of Contents

  RT200/RT230 USER MANUAL CONTENTS Barcode Printer Box Content Getting To Know Your Printer Printer Setup Open The Printer Loading The Ribbon Loading The Label Roll Module Connecting The Printer To The Host Computer Installing Printer Driver and GoLabel with Super Wizard CD…

• Page 3
  RT200/RT230 USER MANUAL FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

• Page 4: Safety Instructions

  RT200/RT230 USER MANUAL SAFETY INSTRUCTIONS Please read the following instructions carefully. Keep the equipment away from humidity. Before you connect the equipment to the power outlet, please check the voltage of the power source. Make sure the printer is off before plugging the power connector into the power jack.

• Page 5: Barcode Printer

  Please check that all of the following items are included with your printer. RT200/RT230 Barcode Printer  Label Stock Ribbon Module Power Adapter    Empty Ribbon Core Power Cord Ribbon AC Adapter USB Cable RT200/RT230 Quick Guide    Including GoLabel software and RT200/RT230 user manual.

• Page 6: Getting To Know Your Printer

  Barcode Printer Getting To Know Your Printer Device Overview Front View  LED INDICATOR OPERATION PANEL FEED BUTTON POWER BUTTON FRONT COVER RELEASE CATCHES Pull catches for opening the printer cover Rear View  FAN-FOLD LABEL INSERT Feed slot for continuous labels ETHERNET PORT AUTO CALIBRATION BUTTON SERIAL PORT…

• Page 7
  Barcode Printer Bottom View  COVER OF THE MODULE CONNECTION JACKS **** Cut-outs are not intended for wall-mount use.
• Page 8
  Barcode Printer The Internal View Of Printer LABEL SUPPLY MODULE TOP COVER PAPER PRESS BAR LABEL SUPPLY HUB RELEASE CATCH Release catch for closing RELEASE CATCH the printer cover Release catch for opening the label supply hub LABEL SENSOR MODULE LABEL GUIDES PLATEN MODULE LABEL SENSOR…

• Page 9: Printer Setup

  Printer Setup Open The Printer Open The Printer Cover And The Printing Mechanism Place the printer on a flat surface. Open the printer cover by pulling the release catches on both sides of the printer and lift the cover. Pull the catches toward the direction Pull the catches toward the direction COVER RELEASE CATCHES Pull the catches for opening the printer cover…

• Page 10: Loading The Ribbon

  Printer Setup Loading The Ribbon A New Ribbon Module Installation A NEW RIBBON EMPTY RIBBON CORE Attach the ribbon to the empty ribbon core with the adhesive strip at the end of the ribbon. Notch on left side Stick on empty ribbon core Wind the ribbon around the empty ribbon core for 2 to 3 circles.

• Page 11
  Printer Setup Load The Ribbon On The Printer For Ribbon Supply Module RIBBON SUPPLY MODULE Place the right-hand side of ribbon first. Push the ribbon to tighten the spring of the holder Right side SPRING OF HOLDER Align the ribbon core to the holder Then place the left-hand side of the ribbon.
• Page 12
  Printer Setup The ribbon supply module loading is completed. Load The Ribbon On The Printer For Ribbon Rewind Module RIBBON REWIND MODULE Pass the ribbon to round the print head. Move the empty ribbon core upward to ribbon rewind mechanism…
• Page 13
  Printer Setup Place the right-hand side of empty ribbon core first. Right side Align the empty ribbon core to the holder Push the empty ribbon core to tighten the spring of the holder SPRING OF HOLDER Then place the left-hand side of the empty ribbon core. Turn the ribbon wheel to align the notch of empty ribbon core to the spoke.

• Page 14: Loading The Label Roll Module

  Printer Setup Loading The Label Roll Module A New Label Supply Module Loading LABEL STOCK LABEL SUPPLY HUB Unlock the release catch to lift the label supply hub. Push rightward Lift the label supply hub upward Place the label stock on the label supply hub. Place on the label supply hub…

• Page 15
  Printer Setup Push the label supply module downward and close the release catch. Push downward to fix the module A new label supply module is completed. Loading The Label Roll Module On The Printer Feed the Label through the label guides and adjust the label guides to the label width. The label guides will help to prevent the label swaying.
• Page 16
  Printer Setup Unlock the release catch to close the printer cover. Push the release catch Close the printer cover Press the FEED key and make sure the label is fed smoothly. The label loading is completed now. **** Please keeps the rack gear clean to ensure the smoothness of label holder.

• Page 17: Connecting The Printer To The Host Computer

  Connect the power cord to the AC adapter. POWER CORD AC ADAPTER Connect the jack of the power adapter to the printer and connect the plug of the power adapter to the socket of the wall. RT200/RT230 BARCODE PRINTER POWER ADAPTER JACK SLOT THE WALL…

• Page 18
  Printer Setup Connect the USB/serial cable to the printer and host computer. RT200/RT230 BARCODE PRINTER USB PORT USB CABLE PLUG PLUG SOCKET Pressing the power button. The power LED indicator should now lights up. Pressing the power button POWER LED INDICATOR…

• Page 19: Installing Printer Driver And Golabel With Super Wizard Cd

  Printer Setup Installing Printer Driver and GoLabel with Super Wizard CD Insert the Super Wizard CD in the CD/DVD drive of the host computer and the program should pop up automatically. You will see the Welcome screen first. On the Welcome screen, choose “Standard Installation”. The wizard will then ask you to make sure your USB and power cables are connected and that the power is turned on.

• Page 20
  Printer Setup As the printer driver and GoLabel are installing, a screen will display a progress bar. Once the installation is complete, you can start to make and print labels with GoLabel or throug the printer driver. As the optional steps, you can also print a test label or register your printer during the “Standard Installation” procedure.
• Page 21
  Insert the product CD in the CD/DVD drive of the host computer and open the «Seagull Drivers» folder on the CD. Select the icon for the driver file and click it to start the installation. Follow the instructions on the screen. The Driver Wizard guides you through the installation procedure. Select «Install printer drivers». Specify your printer model. Godex RT200…
• Page 22
  Specify the port used to connect the printer to the host computer. Enter a printer name and assign the appropriate rights. Godex RT200 Once the installation is complete, a summary of the printer settings is displayed. Check whether the printer settings are correct and click «Finish» to start copying the driver files.
• Page 23
  Printer Setup Once the driver installation is complete, the new printer should appear in the «Printers and Faxes» folder. Godex RT200 Godex RT200…

• Page 24: Operation Panel

  Printer Setting And Control Operation Panel Operation Panel Introduction POWER LED STATUS LED OPERATION PANEL FEED BUTTON POWER BUTTON POWER Button Press the POWER button and the LED indicator lights up green. The printer is on “ Ready to print “ status now. When printer is turned on, keep pressing the POWER button for 3 seconds will turn the printer off.

• Page 25: Label Calibration And Self Test 021

  The printer will now measure the label stock and store the label height. Once the printer has successfully measured the label stock, it will print a self-test label. The contents of a self-test printout are listed below. RT200:GX.XXX Model & Version USB S/N:12345678…

• Page 26
  Operation Panel Auto Label Calibration Button Keep pressing AUTO CALIBRATION button for 1 second, the printer can immediately run the label size calibration. AUTO CALIBRATION BUTTON Press Calibration button can be used to find correct printing position or eliminate the “Media Error” problem. Press…

• Page 27: Error Alerts 023

  Operation Panel Error Alerts In the event of a problem that prevents normal functioning of the printer, you will see an error message on LED indicators and hear some beep signals. Please refer to below table for the error alerts. Error Light POWER LED Colour…

• Page 28: Netsetting For Ethernet 024

  NetSetting for Ethernet Installing The NetSetting software The NetSetting software is used to manage the network configurations when connecting the printer via Ethernet port. It is available on product CD or can be downloaded from official website. To install the NetSetting, please follow below steps.

• Page 29: The Interface Of Netsetting 025

  PC. RT200 Click the magnifier icon to search the Godex printers which are connected via Ethernet port in you network environment. Once a connected Godex printer is detected, it will be listed on the start page.

• Page 30
  NetSetting for Ethernet IP Setting The IP Setting tab can change the printer name, Port number, Gateway setting and the password for configuring the printer. You can also set the printer’s IP address ether by DHCP or by Static IP. You can press “Set”…
• Page 31
  NetSetting for Ethernet Alert Path Setting NetSetting will send the alert messages to designated mail account when the error happened on printer. The alert messages are sent by SMTP (Simple Mail Transfer Protocol) or SNMP (Simple Network Management Protocol). You can set or change the configurations of SMTP and SNMP on this “Alert Path Setting” tab. You can press “Set”…
• Page 32
  NetSetting for Ethernet Alert Message Setting For the alert message notification function, you can decide which error cases need to be sent out to the operator. Moreover, the alert messages can be set to be sent by SMTP, SNMP or both. You can press “Set”…
• Page 33
  Set or change the configurations of connected printer. Most of key settings for the printer operation can be done by this setting page. RT200 You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.
• Page 34
  NetSetting for Ethernet User Command The “User Command” tab provides a communication interface for operator to control the printer. Input printer commands in «Input Command» window and press “Send Command” button, the commands will be sent to the printer. For some commands that will return response message, the message will be displayed in «Output Message» window. You can press “Send Command”…
• Page 35
  “Start Download Firmware” button. The printer firmware then can be updated remotely. BOOT : 1.000a1 F/W : RT200 1.000a In addition to the firmware update, you can press “Recover To Factory Settings” button to restore the printer…

• Page 36: Accessories 032

  Accessories Preparation Steps Before installing the optional modules, please make some preparations as follows. Turn off the printer Remember to switch off the printer before installing any module. Open the printer cover and the printing mechanism Open the printer cover by pulling the release catches on both sides of the printer and lift the cover. Please see the Section 2.1 for further information about Open The Printer.

• Page 37
  Accessories Remove the platen Lift up the release clips on both sides of the platen to release and pull upward the platen. Release the clip CLIP Pull up the platen Ribbon loading Please see the Section 2.2 for further information about Loading The Ribbon. Label loading Please see the Section 2.3 for further information about Loading The Label Roll Module.

• Page 38: Installing The Label Dispenser 034

  Accessories Installing The Label Dispenser The Overview Of The Label Dispenser PAPER SENSOR PAPER FEED ROLLER CONNECTION CABLE OF LABEL DISPENSER COVER Preparation Steps Please see the Section 5.1 Preparation Steps to complete the preparation steps before installing the label dispenser. Installing The Label Dispenser Pass the connection cable through the slot of the printer.

• Page 39
  Accessories Place label dispenser to align both holes of screw and then tighten the screws. Place the platen back to the printer and lock the clips. Lock the clip CLIP Close the top cover and printing mechanism. Turn the printer upside down.
• Page 40
  Accessories Open the cover on the bottom of printer. COVER OF THE MODULE CONNECTION JACKS Open the cover Plug the connector fo the label dispenser to the jack. Plug JACK CONNECTOR OF THE CONNECTION CABLE Close the cover of the module connection jacks. COVER OF THE MODULE CONNECTION JACKS Close the cover ****The printer must be switched off when plugging the connector, or the motherboard may be destroyed!
• Page 41
  Accessories Loading Label Roll With The Label Dispenser Module Remove the first label from the label stock. LABEL STOCK LABEL LINER Tear a label THE FIRST LABEL Feed the Label stock through the label guides. Through the label guides Pull the label liner through the platen and the steel of the label dispenser. LABEL LINER PLATEN STEEL…
• Page 42
  Accessories The feeding path of label and liner should be as shown in below graphic. LABEL LABEL LINER PLATEN LABEL STOCK ROLLER Close the label dispenser and printer cover. The installation is completed now. Close the cover…
• Page 43
  Accessories Press the FEED button to feed the label. The label will be peeled from the liner while it passes through the label dispenser. Press the feed key LABEL LABEL LINER **** There is a paper sensor on the Label Dispenser module. It will stop the printing if it is covered by label. Remove the last printed label and the printer will then continue to print next label.

• Page 44: Installing The Cutter 040

  Accessories Installing The Cutter The Overview Of The Cutter CONNECTION CABLE OF CUTTER FEED-OUT SLOT COVER Preparation Steps Please see the Section 5.1 Preparation Steps to complete the preparation steps before installing the cutter. Installing The Cutter Pass the connection cable through the slot of the printer. ****Remember to switch off the printer before installing the cutter.

• Page 45
  Accessories Place the cutter to align both holes of screw and then tighten the screws. Place the platen back to the printer and lock the clips. Lock the clip CLIP Close the top cover and printing mechanism. Turn the printer upside down.
• Page 46
  Accessories Open the cover on the bottom of printer. COVER OF THE MODULE CONNECTION JACKS Open the cover Plug the connector for the cutter to the jack. Plug JACK CONNECTOR OF THE CONNECTION CABLE Close the cover of the module connection jacks. COVER OF THE MODULE CONNECTION JACKS Close the cover ****The printer must be switched off, or the motherboard may be destroyed!
• Page 47
  Accessories Installing The Label Roll Module On The Printer Pass the labels through the guides and the cutter. Through the label guides Through the cutter Close the top cover and printing mechanism. To finish, press the FEED button to set the label position. Close the top cover Press the feed key ****We advise against using inside wound label stock.

• Page 48: Maintenance And Adjustment 044

  Maintenance And Adjustment Cleaning The Print Head Dirt on the print head or ribbon, or glue residue from the label stock may result in inadequate print quality. The printer cover must therefore always be closed during printing. Keeping dirt and dust away from the paper or labels ensures a good print quality and a longer lifespan of the print head.

• Page 49: Troubleshooting 045

  Maintenance And Adjustment Troubleshooting Problem Solution ♦ Check the power supply. The printer is switched on but the LED does not light up. Please see the Section 2.4 Check the software settings (driver settings) or command codes. ♦ Look for the error alert in the table in Section 3.3. Error Alerts. ♦…

• Page 50: Appendix

  RT200/RT230 USER MANUAL APPENDIX PRODUCT SPENIFICATIONS RT200 RT230 Model Print Method Thermal Transfer / Direct Thermal Resolution 203 dpi (8 dots/mm) 300 dpi (12 dots/mm) Print Speed 5 IPS (127 mm/s) 4 IPS (102 mm/s) Print Width 2.12” (54 mm) 2.24”…

• Page 51
  ** Minimum print height and maximum print speed specification compliance can be dependent on non-standard material variables such as label type, thickness, spacing, liner construction, etc. Godex is pleased to test non-standard materials for minimum print height and maximum print speed capability.

• Page 52: Interface

  RT200/RT230 USER MANUAL APPENDIX INTERFACE Pinout Description  Connector Type : Type B Pin NO. Function VBUS Serial Port  Default settings： Baud rate 9600, no parity, 8 data bits, 1 stop bit, XON/XOFF protocol and RTS/CTS RS232 Housing(9-pin to 9-pin)

MANUALSCAT | RU

Вопросы и ответы

У вас есть вопрос о Godex RT200, но вы не можете найти ответ в пользовательском руководстве? Возможно, пользователи ManualsCat.com смогут помочь вам и ответят на ваш вопрос. Заполните форму ниже — и ваш вопрос будет отображаться под руководством для Godex RT200. Пожалуйста, убедитесь, что вы опишите свои трудности с Godex RT200 как можно более детально. Чем более детальным является ваш вопрос, тем более высоки шансы, что другой пользователь быстро ответит на него. Вам будет автоматически отправлено электронное письмо, чтобы проинформировать вас, когда кто-то из пользователей ответит на ваш вопрос.