Мануал хонда форза 250 mf06 на русском языке

Как перевести мили в километры?

В чем разница между топливом E10 и E5?

Как удалить ржавчину с устройства Honda Скутер?

Инструкция Honda Forza 250 (2015) доступно в русский?

Page: 1

Contents
Scooter Safety P. 2
Operation Guide P. 16
Maintenance P. 40
Troubleshooting P. 81
Information P. 97
Specifications P. 119
Index P. 123

Page: 2

Welcome
Congratulations on your purchase of a new
Honda scooter. Your selection of a Honda
makes you part of a worldwide family of
satisfied customers who appreciate Honda’s
reputation for building quality into every
product.
To ensure your safety and riding pleasure:
● Read this owner’s manual carefully.
● Follow all recommendations and
procedures contained in this manual.
● Pay close attention to safety messages
contained in this manual and on the
scooter.
To protect your investment, we urge you to
take responsibility for keeping your scooter
well serviced and maintained.
Also, observe the break-in guidelines, and
always perform the pre-ride inspection and
other periodic checks in this manual.
When service is required, remember that
your Honda dealer knows your scooter best.
If you have the required mechanical “know-
how” and tools, you can purchase an official
Honda Service Manual to help you perform
many maintenance and repair tasks. 2 P. 114
Read the warranty information thoroughly so
that you understand the warranty coverage
and that you are aware of your rights and
responsibilities. 2 P. 115
You may also want to visit our website at
www.powersports.honda.com.
www.honda.ca.
Happy riding!
California Proposition 65 Warning
WARNING: This product contains or emits
chemicals known to the State of California to
cause cancer and birth defects or other
reproductive harm.
Canada

Page: 3

A Few Words About Safety
Your safety, and the safety of others, is very
important. Operating this scooter safely is an
important responsibility.
To help you make informed decisions about
safety, we have provided operating
procedures and other information on safety
labels and in this manual. This information
alerts you to potential hazards that could
hurt you or others.
Of course, it is not practical or possible to
warn you about all hazards associated with
operating or maintaining a scooter. You
must use your own good judgment.
You will find important safety information in
a variety of forms, including:
● Safety labels on the scooter.
● Safety Messages preceded by a safety alert
symbol and one of three signal words:
DANGER, WARNING, or CAUTION.
These signal words mean:
3DANGER
You WILL be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
3WARNING
You CAN be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
3CAUTION
You CAN be HURT if you don’t follow
instructions.
Other important information is
provided under the following titles:
NOTICE Information to help you avoid
damage to your scooter, other
property, or the environment.

Page: 4

Scooter Safety
This section contains important information for safe riding of your scooter.
Please read this section carefully.
Safety Guidelines …………………………………..P. 3
Safety Labels …………………………………………P. 7
Safety Precautions …………………………………P. 9
Riding Precautions ……………………………….P. 10
Accessories & Modifications………………….P. 14
Loading ……………………………………………….P. 15

Page: 5

Safety Guidelines
3
continued
Scooter
Safety
Safety Guidelines
Follow these guidelines to enhance your safety:
● Perform all routine and regular inspections
specified in this manual.
● Stop the engine and keep sparks and flame
away before filling the fuel tank.
● Do not run the engine in enclosed or partly
enclosed areas. Carbon monoxide in exhaust
gases is toxic and can kill you.
It’s a proven fact: helmets and protective
apparel significantly reduce the number and
severity of head and other injuries. So always
wear an approved motorcycle helmet and
protective apparel. 2 P. 9
Make sure that you are physically fit, mentally
focused and free of alcohol and drugs. Check
that you and your passenger are both wearing
an approved motorcycle helmet and protective
apparel. Instruct your passenger on holding
onto the grab rail or your waist, leaning with
you in turns, and keeping their feet on the
footpegs, even when the scooter is stopped.
Even if you have ridden other scooters, practice
riding in a safe area to become familiar with
how this scooter works and handles, and to
become accustomed to the scooter’s size and
weight.
Always Wear a Helmet
Before Riding
Take Time to Learn & Practice

Page: 6

Safety Guidelines
4
Scooter
Safety
We recommend that all riders take a certified
course approved by the Motorcycle Safety
Foundation (MSF). New riders should start with
the basic course, and even experienced riders
will find the advanced course beneficial. For
information about the MSF training course
nearest you, call the national toll-free number:
(800) 446-9227.
Other riding tips can be found in the You
and Your Scooter Riding Tips booklet that came
with your scooter.
Always pay attention to other vehicles around
you, and do not assume that other drivers see
you. Be prepared to stop quickly or perform an
evasive maneuver.
Make yourself more visible, especially at night,
by wearing bright reflective clothing,
positioning yourself so other drivers can see
you, signaling before turning or changing lanes,
and using your horn when necessary.
Never ride beyond your personal abilities or
faster than conditions warrant. Fatigue and
inattention can impair your ability to use good
judgment and ride safely.
Alcohol and riding don’t mix. Even one
alcoholic drink can reduce your ability to
respond to changing conditions, and your
reaction time gets worse with every additional
drink. Don’t drink and ride, and don’t let your
friends drink and ride either.
Ride Defensively
USA
Make Yourself Easy to See
Ride within Your Limits
Don’t Drink and Ride

Page: 7

Safety Guidelines
5
continued
Scooter
Safety
It’s important to keep your scooter properly
maintained and in safe riding condition.
Inspect your scooter before every ride and
perform all recommended maintenance. Never
exceed load limits (2 P. 15), and do not modify
your scooter or install accessories that would
make your scooter unsafe (2 P. 14).
Personal safety is your first priority. If you or
anyone else has been injured, take time to
assess the severity of the injuries and whether it
is safe to continue riding. Call for emergency
assistance if needed. Also follow applicable
laws and regulations if another person or
vehicle is involved in the crash.
If you decide to continue riding, first evaluate
the condition of your scooter. If the engine is
still running, turn it off. Inspect for fluid leaks,
check the tightness of critical nuts and bolts,
and check the handlebar, control levers, brakes,
and wheels. Ride slowly and cautiously.
Your scooter may have suffered damage that is
not immediately apparent. Have your scooter
thoroughly checked at a qualified service facility
as soon as possible.
Keep Your Honda in Safe Condition
If You are Involved in a Crash

Page: 8

Safety Guidelines
6
Scooter
Safety
Exhaust contains poisonous carbon monoxide,
a colorless, odorless gas. Breathing carbon
monoxide can cause loss of consciousness and
may lead to death.
If you run the engine in confined or even partly
enclosed area, the air you breathe could contain
a dangerous amount of carbon monoxide.
Never run your scooter inside a garage or other
enclosure.
Carbon Monoxide Hazard 3WARNING
Carbon monoxide gas is toxic.
Breathing it can cause
unconsciousness and even kill you.
Avoid any areas or activities that
expose you to carbon monoxide.

Page: 9

Safety Labels
7
continued
Scooter
Safety
Safety Labels
Safety and information labels on your scooter
provide important safety information and may
warn you of potential hazards that could cause
serious injury. Read these labels carefully and
don’t remove them. If a label comes off or
becomes hard to read, contact your dealer for a
replacement.

Page: 10

Safety Labels
8
Scooter
Safety

Page: 11

Safety Precautions
9
continued
Scooter
Safety
Safety Precautions
● Ride cautiously and keep your hands on the
handlebar and feet on the floor.
● Keep passenger’s hands on the grab rail or
your waist, and feet on the footpegs while
riding.
● Always consider the safety of your passenger,
as well as other drivers and riders.
Make sure that you and any passenger are
wearing an approved motorcycle helmet, eye
protection, and high-visibility protective
clothing. Ride defensively in response to
weather and road conditions.
❙ Helmet
Should be safety-standard certified, high-
visibility, and correct size for your head.
● Must fit comfortably but securely, with the
chin strap fastened.
● Face shield with unobstructed field of vision
or other approved eye protection.
Look for a DOT (Department of
Transportation) certification label on any helmet
you buy.
❙ Gloves
Full-finger leather gloves with high abrasion
resistance.
Protective Apparel
3WARNING
Not wearing a helmet increases the
chance of serious injury or death in a
crash.
Make sure that you and any passenger
always wear an approved helmet and
protective apparel.
USA

Page: 12

Riding Precautions
10
Scooter
Safety
❙ Boots or Riding Shoes
Sturdy boots with non-slip soles and ankle
protection.
❙ Jacket and Pants
Protective, highly visible, long-sleeved jacket
and durable long pants for riding (or a
protective suit).
Riding Precautions
During the first 300 miles (500 km) of running,
follow these guidelines to ensure your scooter’s
future reliability and performance.
● Avoid full-throttle starts and rapid
acceleration.
● Avoid hard braking.
● Ride conservatively.
Observe the following guidelines:
● Avoid excessively hard braking.
u Sudden braking can reduce the scooter’s
stability.
u Where possible, reduce speed before
turning; otherwise you risk sliding out.
● Exercise caution on low traction surfaces.
u The tires slip more easily on such surfaces
and braking distances are longer.
Break-in Period
Brakes

Page: 13

Riding Precautions
11
continued
Scooter
Safety
● Avoid continuous braking.
u Repeated braking, such as descending
long steep slopes can seriously overheat
the brakes, reducing their effectiveness.
● For full brake effectiveness, operate both the
front and rear brakes together.
❙ Combi Brake
Your scooter’s rear brake system is linked to the
front brake. This means that operating the rear
brake lever applies the rear brake and a portion
of the front brake. Operating the front brake
lever applies only the front brake.
For full braking effectiveness, operate both the
front and rear brakes together.
❙ Combined ABS
Your scooter’s rear brake system is linked to the
front brake. This means that operating the rear
brake lever applies the rear brake and a portion
of the front brake. Operating the front brake
lever applies only the front brake.
For full braking effectiveness, operate both the
front and rear brakes together.
This model is also equipped with an Anti-lock
Brake System (ABS) designed to help prevent
the brakes from locking up during hard braking.
● ABS does not reduce braking distance. In
certain circumstances, ABS may result in a
longer stopping distance.
● ABS does not function at speeds below 6
mph (10 km/h).
● The brake levers may recoil slightly when
applying the brakes. This is normal.
● Always use the recommended tires to ensure
correct ABS operation.
❙ Wet or Rainy Conditions
Road surfaces are slippery when wet, and wet
brakes further reduce braking efficiency.
Exercise extra caution when braking in wet
conditions.
If the brakes get wet, apply the brakes while
riding at low speed to help them dry.
NSS300
NSS300A

Page: 14

Riding Precautions
12
Scooter
Safety
● Park on a firm, level surface.
● If you must park on a slight incline or loose
surface, park so that the scooter cannot
move or fall over.
● Make sure that high-temperature parts
cannot come into contact with flammable
materials.
● Do not touch the engine, muffler, brakes and
other high-temperature parts until they cool
down.
● To reduce the likelihood of theft, always lock
the handlebar and remove the key and close
the shutter when leaving the scooter
unattended. Use of an anti-theft device is
also recommended.
❙ Parking with the Side Stand or Center Stand
1. Stop the engine.
2. Activate the parking brake. 2 P. 27
3. Using the side stand
Push the side stand down.
Slowly lean the scooter to the left until its
weight rests on the side stand.
Using the center stand
To lower the center stand, stand on the left
side of the scooter. Hold the left handle grip
and the left grab rail. Press down on the tip of
the stand with your right foot and,
simultaneously, pull up and back.
Parking
USA
Left handle grip
Grab rail Center stand

Page: 15

Riding Precautions
13
Scooter
Safety
4. Turn the handlebar fully to the left.
u Turning the handlebar to the right reduces
stability and may cause the scooter to fall.
5. Turn the ignition switch to the LOCK
position, remove the key and close the
shutter. 2 P. 25, 26
Follow these guidelines to protect the engine
and catalytic converter:
● Use only unleaded gasoline.
● Use recommended octane number. Using
lower octane gasoline will result in decreased
engine performance.
● Do not use fuels containing a high
concentration of alcohol. 2 P. 113
● Do not use stale or contaminated gasoline or
an oil/gasoline mixture.
● Avoid getting dirt or water in the fuel tank.
Refueling and Fuel Guidelines

Page: 16

Accessories & Modifications
14
Scooter
Safety
Accessories &
Modifications
We strongly advise that you do not add any
accessories that were not specifically designed
or approved for your scooter by Honda or make
modifications to your scooter from its original
design. Doing so can make it unsafe.
Modifying your scooter may also void your
warranty and make your scooter illegal to
operate on public roads and highways. Before
deciding to install accessories on your scooter
be certain the modification is safe and legal.
Do not pull a trailer with, or attach a sidecar to,
your scooter. Your scooter was not designed for
these attachments, and their use can seriously
impair your scooter’s handling.
3WARNING
Improper accessories or modifications
can cause a crash in which you can be
seriously hurt or killed.
Follow all instructions in this owner’s
manual regarding accessories and
modifications.

Page: 17

Loading
15
Scooter
Safety
Loading
● Carrying extra weight affects your scooter’s
handling, braking and stability. Always ride at
a safe speed for the load you are carrying.
● Avoid carrying an excessive load and keep
within specified load limits.
2 Maximum weight capacity / Maximum
luggage weight P. 119
● Tie all luggage securely, evenly balanced and
close to the center of the scooter.
● Do not place objects near the lights or the
muffler.
3WARNING
Overloading or improper loading can
cause a crash and you can be seriously
hurt or killed.
Follow all load limits and other
loading guidelines in this manual.

Page: 18

16
Operation
Guide
Parts Location
Engine oil drain bolt (P67)
Front brake fluid reservoir
(P74)
Throttle grip (P78)
Engine oil fill cap/dipstick
(P65)
Document bag (P37)
Luggage box (P37)
Battery (P59)
Fuse box 1, Main fuse 1
(P93)
Tool kit (P37)
Coolant reserve tank (P72)
Right fairing pocket (P38)
Parking brake grip
(P27)
USA
Fuse box 2, 3 (P95)
Main fuse 2 (P96)

Page: 19

17
Operation
Guide
Side stand (P77)
Left fairing pocket (P38)
Helmet holder (P36)
Seat (P35)
Crankcase breather (P79)
Oil filter (P66)
Center stand (P12)
Spark plug (P62)
Rear brake fluid reservoir
(P74)
Fuel fill cap (P34)
Air Cleaner (P69)
Belt case air cleaner (P70)

Page: 20

18
Operation
Guide
Instruments
button
MODE
Speedometer
This shows your speed in miles per hour (mph) and/or
kilometer per hour (km/h) depending on vehicle type.
Tachometer
NOTICE
Do not operate the engine in the tachometer red zone.
Excessive engine speed can adversely affect engine life.
button
RESET
Tachometer red zone
(excessive engine rpm range)
Fuel gauge
Needle in the red (E) mark,
remaining fuel approximately
0.95 US gal (3.6 liters)
Coolant temperature gauge ( )
Displays the temperature of the engine
coolant.
NOTICE
Riding with the needle in the H (Hot) range may
cause serious engine damage.
If the needle enters the H (Hot)
range: (P83)

Page: 21

19
Operation
Guide
continued
Display Check
When the ignition switch is turned ON, all the meter and gauge needles swing to the
maximum scale on the dial once, all the mode and digital segments will show. If any part
of these displays does not come on when it should, have your dealer check for problems.
Odometer [TOTAL] & Tripmeter [TRIP A/B]
button switches between odometer &
tripmeters.
Odometer & tripmeter read in miles.
Odometer & tripmeter read in
kilometers.
• Odometer: Total distance ridden.
• Tripmeter: Distance ridden since tripmeter
was reset (press and hold button to
reset to 0.0 mile (0.0 km)).
• When you reset the tripmeter, the average
fuel consumption meter is reset at the same
time.
MODE
USA
Canada
RESET
Clock
To set the clock: (P21)
Average fuel consumption meter (P20)

Page: 22

20
Instruments (Continued)
Operation
Guide
Average fuel consumption meter
Shows average fuel consumption in mile/gal, km/ℓ or ℓ/100km based on the tripmeter A.
Select the mile/gal, km/ℓ or ℓ/100km, press and hold the MODE button with the tripmeter.
After you reset the tripmeter A, the average fuel consumption meter shows “ ”.
SELECT SELECT
SELECT
RESET RESET RESET

Page: 23

21
Operation
Guide
To set the clock:
!a Turn the ignition switch ON.
!b Press and hold and
buttons until the hour digits start flashing.
!c Press button until the desired hour
is displayed.
u Press and hold to advance the hour fast.
!d Press button. The minute digits
start flashing.
MODE RESET
RESET
MODE
!e Press button until the desired
minute is displayed.
u Press and hold to advance the minute
fast.
!f Press button. The clock is set.
u The time can also be set by turning the
ignition switch OFF.
The display will stop flashing
automatically and the adjustment will be
cancelled if the button is not pressed for
about 2 minutes.
RESET
MODE

Page: 24

22
Operation
Guide
Indicators
Comes on briefly when the ignition switch is turned
ON with the engine stop switch in the RUN
position.
If it comes on while engine is running: (P84)
PGM-FI (Programmed Fuel Injection)
malfunction indicator lamp (MIL)
ABS (Anti-lock Brake System) indicator
Comes on when the ignition switch is turned ON.
Goes off when your speed reaches approximately
6 mph (10 km/h).
If it comes on while riding: (P85)
NSS300A
Low oil pressure indicator
Comes on when the ignition switch
is turned ON.
Goes off when the engine starts.
If it comes on while engine is
running: (P84)
Parking brake indicator
Lights as a reminder that you have not
released the parking brake grip.
(P27)
USA

Page: 25

23
Operation
Guide
High beam
indicator
Left turn signal indicator
Right turn
signal indicator
OIL CHANGE indicator
• Comes on briefly when ignition
switch is turned on.
•
Lights when the distance reaches
about 600 mile (960 km) for the
first time and every 8,000 mile
(12,800 km) after resetting the
indicator.
Lights when the distance reaches
about 1,000 km (625 mile) for the
first time and every 12,800 km
(8,000 mile) after resetting the
indicator.
u The indicator does not go off until
it is reset.
To reset the indicator, press and
hold button while turning
the ignition switch to the ON
position, and keep hold
button for more than 3 seconds.
USA
Canada
RESET
RESET

Page: 26

24
Operation
Guide
Switches
Start button
Horn button
Turn signal switch
u Pressing the switch turns the turn
signal off.
Headlight dimmer switch
• : High beam
• : Low beam
Engine stop switch
Should normally remain in the
RUN position.
u In an emergency, switch to the
OFF position (the starter
motor will not operate) to stop
the engine.
Hazard switch
Switchable when the ignition
switch is ON.
Canada

Page: 27

25
continued
Operation
Guide
Steering Lock
Lock the steering when parking to help
prevent theft.
A U-shaped wheel lock or similar device is
also recommended.
❙ Locking
!a Turn the handlebar all the way to the left.
!b Push the key down, and turn the ignition
switch to the LOCK position.
u Jiggle the handlebar if the lock is difficult
to engage.
!c Remove the key.
❙ Unlocking
Insert the key and turn the ignition switch to
the OFF position.
Ignition Switch
Switches the electrical system on/off,
locks the steering, and operates the
box opener switch, fuel lid and seat
opener switch.
u Key can be removed when in the OFF
or LOCK position.
ON
Turns electrical system on for starting/riding.
OFF
Turns engine off.
LOCK
Locks steering.
OPENER
Operates the box opener switch, fuel lid and
seat opener switch.
Push
Ignition key
!a
!b
Turn

Page: 28

26
Switches (Continued)
Operation
Guide
Shutter
The ignition switch for this scooter is
equipped with a shutter. After parking the
scooter, close the shutter for theft
prevention.
❙ Close
!a Remove the ignition key from the ignition
switch.
!b Align the projection of the shutter key with
the slot of the shutter, and turn the shutter
key counterclockwise.
u You can also close the shutter by moving
the knob upward without the shutter
key.
!c Remove the key.
❙ Open
Align the projection of the shutter key with
the slot of the shutter, and turn the shutter
key clockwise.
Ignition
key
Open
Close
Close
Shutter key
Projection
Slot
Knob

Page: 29

27
Operation
Guide
Parking Brake
Parking Brake Grip
Be sure the parking brake is applied while
parking and warming up the engine.
u Make sure the parking brake grip is released
before riding.
Pull the parking brake grip back to lock the
rear wheel.
u The parking brake lock will not function if
the parking brake is not adjusted properly.
(P76)
Release the parking brake grip by lightly
pulling in the grip.
u Before riding, check that the parking brake
indicator is turned off and make sure that the
parking brake is fully released so there is no
drag on the rear wheel.
USA
Parking brake grip
Apply
Pull
Release
Release
Lightly pull

Page: 30

28
Operation
Guide
Starting the Engine
Start your engine using the following
procedure, regardless of whether the engine
is cold or warm.
This scooter is equipped with a side stand
ignition cut-off system.
u If the side stand is down, the engine cannot
be started.
u If you lower the side stand with the engine
running, it will automatically shut off.
!a Place the scooter on its center stand.
!b Lock the parking brake. (P27)
!c Make sure the engine stop switch is in the
RUN position.
!d Turn the ignition switch to the ON position.
NOTICE
• If the engine does not start within 5 seconds, turn the
ignition off and wait 10 seconds before trying to start
the engine again to recover battery voltage.
• Extended fast idling and revving the engine can
damage the engine, and the exhaust system.
• The engine will not start if the throttle is fully open.
USA
!c
!d

Page: 31

29
Operation
Guide
continued
!e Squeeze the rear brake lever.
u The starter motor will only work when
the rear brake lever is squeezed and the
side stand is up.
!f Press the start button with the throttle
completely closed. Release the start button
as soon as the engine starts.
!f
!e
If you cannot start the engine:
!a Place the scooter on its center stand and
squeeze the rear brake lever.
!b With the throttle slightly open (about 1/8 in
[3 mm]), press the start button.
About 1/8 in (3 mm)

Page: 32

30
Starting the Engine (Continued)
Operation
Guide
If the engine does not start:
!a Open the throttle fully and press the start
button for 5 seconds.
!b Repeat the normal starting procedure.
!c If the engine starts, open the throttle slightly
if idling is unstable.
!d If the engine does not start, wait 10 seconds
before trying steps !a & !b again.
❙ If Engine Will Not Start (P82)

Page: 33

31
continued
Operation
Guide
Riding
Starting the Scooter
!a Push the scooter forward off the center
stand.
u Lock the parking brake.
Squeeze the rear brake lever.
u Keep throttle closed.
Make sure the side stand and center stand
are up.
!b Get on the scooter.
u Mount the scooter from the left side,
keeping at least one foot on the ground.
!c Release the parking brake.
u To prevent unexpected movement,
squeeze brake lever.
!d Release the rear brake lever.
!e Acceleration and deceleration.
To accelerate: Open the throttle slowly.
To decelerate: Close the throttle.
USA
Canada
USA
Close (Decelerate)
Open (Accelerate)

Page: 34

32
Riding (Continued)
Operation
Guide
Braking
Close the throttle and apply the front and
rear brake levers together.
Do not apply the parking brake while riding.
It may cause the rear wheel to lock, reducing
control of the scooter.
USA
Rear brake lever Front brake lever

Page: 35

33
continued
Operation
Guide
Refueling
Fuel type: Unleaded gasoline only
Recommended fuel octane number:
Pump Octane Number (PON) 86 or higher.
Tank capacity: 3.04 US gal (11.5 liters)
❙ Refueling and Fuel Guidelines (P13)
Opening the Fuel Fill Cap
!a Insert the ignition key and turn it to the
position of OPENER.
!b Push the FUEL side of the fuel lid and seat
opener switch.
u The fuel lid opens.
Fuel lid
FUEL
OPENER
Ignition key
Fuel lid and seat
opener switch

Page: 36

34
Refueling (Continued)
Operation
Guide
!c Turn the fuel fill cap counterclockwise and
remove the fuel fill cap.
Do not fill with fuel above the lower edge of
the filler neck.
Closing the Fuel Fill Cap
!a Install and tighten the fuel fill cap firmly by
turning it clockwise.
u Make sure that the arrow marks on the
fuel fill cap and fuel tank are aligned.
!b Close the fuel lid until it locks.
u Make sure that the fuel lid is closed
securely.
Lower edge of
filler neck
Fuel fill cap Arrow marks
3WARNING
Gasoline is highly flammable and
explosive. You can be burned or
seriously injured when handling fuel.
• Stop the engine, and keep heat,
sparks, and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.

Page: 37

35
continued
Operation
Guide
Storage Equipment
To open the seat
!a Insert the ignition key and turn it to the
position of OPENER.
!b Push the SEAT side of the fuel lid and seat
opener switch.
!c Open the seat.
To close the seat
Close and push down on the rear of the seat
until it locks. Make sure that the seat is
locked securely by pulling it up lightly.
Take care not to lock your key in the
compartment under the seat.
Seat
OPENER
Ignition key
Fuel lid and seat
opener switch
SEAT

Page: 38

36
Storage Equipment (Continued)
Operation
Guide
Helmet Holder
The helmet holder is located under the seat.
A helmet set wire is in the tool kit.
u Use the helmet holder only when parked.
u Securely insert the helmet holder into the slot
when closing the seat.
❙ Opening the seat. (P35)
Helmet
D-ring
Helmet set
wire
Helmet
holder
Slot
Helmet set
wire
3WARNING
Riding with a helmet attached to the
holder can interfere with the rear
wheel or suspension and could cause a
crash in which you can be seriously
hurt or killed.
Use the helmet holder only while
parked. Do not ride with a helmet
secured by the holder.

Page: 39

37
Operation
Guide
continued
Two helmets can be stored in the luggage
box. Set the helmets as shown.
u Make sure to turn the rear side helmet to
face the right side while the front side helmet
faces the front.
u Some helmets may not fit in the
compartment due to their size or design.
Helmet
Luggage box
Luggage Box
Never exceed the maximum weight limit.
Maximum Weight: 22 lb (10 kg)
u Do not store any items that are flammable or
susceptible to heat damage.
u Do not store valuables or fragile articles.
Tool Kit/Document Bag
The tool kit and document bag are in the
luggage box.
Tool kit Document bag

Page: 40

38
Storage Equipment (Continued)
Operation
Guide
Left Fairing Pocket
❙ Open
!a Insert the ignition key and turn it to the
position of OPENER.
!b Push BOX side of the box opener switch.
❙ Close
Close the left fairing pocket lid until it locks.
Right Fairing Pocket
❙ Open
Pull the knob up, then open the right fairing
pocket lid.
❙ Close
Close the right fairing pocket lid.
The maximum allowable load in the left and
right fairing pocket shall be no more than:
Left Fairing Pocket 3.3 lb (1.5 kg)
Right Fairing Pocket 1.0 lb (0.5 kg)
Make sure that the left and right fairing
pocket lid are closed securely.
u Do not store valuables or fragile articles. Especially
the right fairing pocket, it does not lock.
Ignition key
Box opener switch
OPENER
Left fairing
pocket lid
Right fairing
pocket lid
Knob

Page: 41

39
Operation
Guide
Accessory Socket
The accessory socket is located in the left
fairing pocket.
Open the left fairing pocket lid to gain access
to the accessory socket.
Rated capacity is 24W (12V, 2A).
Accessory socket Cover
u To prevent the battery run down or weak the
battery, keep the engine running while
drawing current from the socket.
u Set the headlight in the low beam. The
battery run down or damage to the
accessory socket causes result.
u To prevent entry foreign matter, be sure to
close the cover when the accessory socket is
not used.
❙ Opening the left fairing pocket. (P38)

Page: 42

Maintenance
Please read “Importance of Maintenance” and “Maintenance Fundamentals”
carefully before attempting any maintenance. Refer to “Specifications” for service
data.
An optional larger tool kit may be available. Check with your Honda dealer’s parts
department.
Importance of Maintenance………………….P. 41
Maintenance Schedule………………………….P. 43
Maintenance Fundamentals………………….P. 46
Removing & Installing Body Components….P. 59
Battery ………………………………………………P. 59
Battery Cover ……………………………………..P. 60
Clip …………………………………………………..P. 61
Spark Plug……………………………………………P. 62
Engine Oil ……………………………………………P. 65
Air Cleaner…………………………………………..P. 69
Coolant………………………………………………..P. 72
Brakes………………………………………………….P. 74
Side Stand ………………………………………….. P. 77
Throttle………………………………………………. P. 78
Crankcase Breather……………………………… P. 79
Other Adjustments ……………………………… P. 80
Headlight Aim……………………………………. P. 80
Rear Suspension…………………………………. P. 80

Page: 43

41
Maintenance
Importance of Maintenance
Keeping your scooter well-maintained is
absolutely essential to your safety and to
protect your investment, obtain maximum
performance, avoid breakdowns, and reduce air
pollution. Maintenance is the owner’s
responsibility. Be sure to inspect your scooter
before each ride, and perform the periodic
checks specified in the Maintenance Schedule.
2 P. 43
For information about the exhaust emission and
noise emission requirements of the U.S.
Environmental Protection Agency (EPA), the
California Air Resources Board (CARB), and
Environment Canada (EC). 2 P. 107
Maintenance, replacement or repair of the
emission control devices and systems may
be performed by any motorcycle repair
establishment or individual using parts
that are “certified“ to EPA standards.
Importance of Maintenance
3WARNING
Improperly maintaining your scooter
or failing to correct a problem before
you ride can cause a crash in which
you can be seriously hurt or killed.
Always follow the inspection and
maintenance recommendations and
schedules in this owner’s manual.
USA

Page: 44

Importance of Maintenance
42
Maintenance
Always read the maintenance instructions
before you begin each task, and make sure that
you have the tools, parts, and skills required.
We cannot warn you of every conceivable
hazard that can arise in performing
maintenance. Only you can decide whether or
not you should perform a given task.
Follow these guidelines when performing
maintenance.
● Stop the engine and remove the key.
● Place your scooter on a firm, level surface
using the side stand, center stand or a
maintenance stand to provide support.
● Allow the engine, muffler, brakes, and other
high-temperature parts to cool before
servicing as you can get burned.
● Run the engine only when instructed, and do
so in a well-ventilated area.
Maintenance Safety

Page: 45

43
continued
Maintenance
Maintenance Schedule
The maintenance schedule specifies the
maintenance requirements necessary to
ensure safe, dependable performance, and
proper emission control.
Maintenance work should be performed in
accordance with Honda’s standards and
specifications by properly trained and
equipped technicians. Your dealer meets all
of these requirements. Keep an accurate
record of maintenance to help ensure that
your scooter is properly maintained. Make
sure that whomever performs the
maintenance completes this record.
All scheduled maintenance is considered a
normal owner operating cost and will be
charged to you by your dealer. Retain all
receipts. If you sell the scooter, these receipts
should be transferred with the scooter to the
new owner.

Page: 46

Maintenance Schedule
44
Maintenance
Maintenance Level
: Intermediate. We recommend service by your dealer, unless you
have the necessary tools and are mechanically skilled.
Procedures are provided in an official Honda Service Manual
(2 P. 114).
: Technical. In the interest of safety, have your scooter serviced
by your dealer.
Maintenance Legend
: Inspect (clean, adjust, lubricate, or replace, if necessary)
: Replace
: Clean
Frequency*1
Refer to
page
Items × 1,000 mi 0.6 4 8 12 16 20 24
× 1,000 km 1.0 6.4 12.8 19.2 25.6 32.0 38.4
Emission-Related
Items
Fuel Line –
Throttle Operation 78
Air Cleaner*2 69
Crankcase Breather*3 79
Spark Plug 62
Valve Clearance –
Engine Oil
Initial = 600 mi (1,000 km) or 1 month:
Regular = Every 8,000 mi (12,800 km) or 12 months: 65
Engine Oil Filter 67
Engine Idle Speed –
Radiator Coolant*5 72
Cooling System –
Secondary Air Supply System –
Evaporative Emission Control System*4 –
I I I
I I I
R R
I R I R I R
I
R
R
R R R R
I I I I I I I
I I R
I I I
I I I
I I
I
R

Page: 47

Maintenance Schedule
45
Maintenance
Notes:
*1 : At higher odometer reading, repeat at the frequency interval
established here.
*2 : Service more frequently when riding in unusually wet or dusty
areas.
*3 : Service more frequently when riding in rain or at full throttle.
*4 : 50 STATE (meets California)
*5 : Replace every 2 years, or at indicated odometer interval,
whichever comes first. Replacement requires mechanical skill.
*6 : Replace every 2 years. Replacement requires mechanical skill.
Frequency*1
Refer to
page
Items × 1,000 mi 0.6 4 8 12 16 20 24
× 1,000 km 1.0 6.4 12.8 19.2 25.6 32.0 38.4
Non-Emission-Related
Items
Drive Belt –
Belt Case Air Cleaner 70
Final Drive Oil*6 –
Brake FLuid*5 74
Brake Pads Wear 75
Brake System 46
Brake Lock Operation 76
Headlight Aim 80
Clutch Shoes Wear –
Side Stand 77
Suspension 80
Nuts, Bolts, Fasteners –
Wheels/Tires 54
Steering Head Bearings –
I R I
I I R I I R
I I I I I I
I I I I
I I I I I I
I I I
I I I I I I
I I I
I I I
I I I I
I I I
I I I I

Page: 48

46
Maintenance
Maintenance Fundamentals
To ensure safety, it is your responsibility to
perform a pre-ride inspection and make sure
that any problem you find is corrected. A pre-
ride inspection is a must, not only for safety, but
because having a breakdown, or even a flat tire,
can be a major inconvenience.
Check the following items before you get on
your scooter:
● Tire tread wear and air pressures are within
limits. 2 P. 54
● Lights, horn, and turn signals operate
normally.
Check the following items if you are carrying a
passenger or cargo:
● Combined weight is within load limits.
2 P. 119
● Cargo is secured properly.
● Suspension spring preload setting is adjusted
to suit load. 2 P. 80
Check the following items after you get on your
scooter:
● Throttle action moves smoothly without
binding. 2 P. 78
● Brake levers operate normally.
● Refuel the remaining fuel and refuel when
needed. 2 P. 18, 33
● Engine stop switch functions properly.
2 P. 24
Check the following items at regular intervals:
● Oil level is between the upper and lower level
marks. 2 P. 65
● Brake fluid level is above the LOWER level
marks. 2 P. 74
● Engine coolant level is between the UPPER
and LOWER level marks. 2 P. 72
● Side stand functions properly. 2 P. 77
● Parking brake works properly. 2 P. 76
Pre-ride Inspection
USA

Page: 49

Maintenance Fundamentals
47
Maintenance
You should also perform other periodic
maintenance checks at least once a month
regardless of how often you ride, or more often
if you ride frequently.
Also, check the odometer reading against the
Maintenance Schedule and perform all
maintenance that is due. 2 P. 43
Periodic Checks
Tires and wheels
Check the air pressure (2 P. 54), examine tread for wear and damage
(2 P. 54), and check the wheels for damage.
Fluid levels
Check the engine oil level (2 P. 65), engine coolant level (2 P. 72),
and brake fluid level (2 P. 74).
Lights
Check that the headlights, brake lights, taillights, turn signals and
license plate light are working properly.
Controls
Check the freeplay of the throttle grip (2 P. 78).
Check the parking brake (2 P. 76) operate properly.
Fuses Check that you have a full supply of spare fuses.
Nuts & bolts Check the major nuts and bolts, and tighten as needed.
Crankcase Breather
Service the crankcase breather more frequently if your scooter is
ridden in the rain or often at full throttle. Service the breather if you
can see deposits in the transparent section of the drain tube (2 P. 79).
USA

Page: 50

Maintenance Fundamentals
48
Maintenance
Always use Honda Genuine Parts or their
equivalents to ensure reliability and safety.
When ordering colored components, specify
the model name, color, and code mentioned on
the color label. The color label is attached to the
luggage box under the seat. 2 P. 35
Replacing Parts
3WARNING
Installing non-Honda parts may make
your scooter unsafe and cause a crash
in which you can be seriously hurt or
killed.
Always use Honda Genuine Parts or
equivalents that have been designed
and approved for your scooter.
Color label