Velodyne cht 10q инструкция на русском

Краткое содержание страницы № 1

S
eries
CHT- 8Q
CHT-10Q
CHT-12Q
CHT-15Q
USER’S
MANUAL
Remote Controlled Home Theater Subwoofers

Краткое содержание страницы № 2

. www.v elodyne.com CHT-Q Series User’s Manual i

Краткое содержание страницы № 3

Table of Contents Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Краткое содержание страницы № 4

Congratulations! Congratulations on your purchase of a Velodyne CHT-Q subwoofer. This system represents the state-of-the-art in low frequency reproduction. Read and follow the instructions below to ensure safe and proper system operation. Note: Do not leave unit in direct sunlight or use in high humidity environments!!! Warning! To prevent fire or shock hazard, do not expose this product to rain or moisture. To avoid electrical shock, do not open the speaker enclosure or amp chassis cover.

Краткое содержание страницы № 5

Prepare for Installation Your new Velodyne subwoofer provides for a number of installation options. Read all of the i nstallation information below in order to determine which installation option is best for your Remember to perform all installation procedures with system power turned off system. to prevent possible damage. Placement The first step in installing your new CHT-Q sub is to determine where it will be placed in the room. Unpack the system carefully and use the following guidelines

Краткое содержание страницы № 6

Installation Inputs Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when connecting your subwoofer to a pre-amp, signal processor (such as LFE out), line- level crossover, or receiver with pre-amp level outputs. When using the line level jacks, some receivers may not provide enough signal to have the unit’s auto-on feature operate properly. Additionally, this lack of signal may also cause the subwoofer to produce less output than it is capable o

Краткое содержание страницы № 7

Phase Adjustment — 0°/90°/180°/270° This control allows you to change the phase of the subwoofer’s output signal to correct for any p ossible mismatch and resulting cancellation between the subwoofer and your main speakers/amplifier. To adjust, simply listen to the system with music playing, then depress the various phase switches on the remote control and listen for a change in mid-bass frequency output. The correct position will have a greater amount of apparent mid-bass frequency output. If

Краткое содержание страницы № 8

Front Panel LED 2 Readout 1 3 MIC Remote Mic Control Jack Sensor Figure 1. CHT-Q Front Panel Following are brief descriptions of the controls and connections described in Figure 1. (1) REMOTE CONTROL SENSOR IR sensor window receives a signal from the included remote control. (2) LED READOUT 2.5 digit, eight segment LED readout displays volume, phase and Auto-EQ. (3) MIC JACK Connector for the supplied microphone to use during the Auto-EQ process. . www.v elodyne.com CHT-Q Series Use

Краткое содержание страницы № 9

Rear Panel Connections 7 6 5 4 3 1 2 Figure 2. CHT-8Q, CHT-10Q, and CHT-12Q Rear Panel Connections Figure 2 shows the controls and connections on the rear panel of the CHT-8Q, CHT-10Q, and CHT-12Q. Following are brief descriptions of the controls and connections described in Figures 2 and 4 and 5. More detail of these connections can be found below: (1) SPEAKER LEVEL INPUT Terminals Connect these input terminals to the speaker output terminals of your amplifier or receiver. If you use this m

Краткое содержание страницы № 10

(2) SPEAKER LEVEL OUTPUT Terminals Sends a crossed-over speaker-level signal to the front speakers. See below for a more detailed explanation of this crossover. (3) IR INPUT This is a connection that allows the utilization of a third party infrared remote sensor, such as Elan or Xantech, or an extended cable for placement closer to your other remote controlled equipment. This keeps you from awkward control angles using the infrared remote control. (4) LINE OUTPUT Connect these jacks to the LIN

Краткое содержание страницы № 11

Low-Pass Crossover Both sets of inputs sum the left and right channels together and the resulting signal is passed through an adjustable low-pass crossover before being amplified. The crossover control allows you to adjust the upper limit of the subwoofer’s frequency response from 40 to 120 Hz. The subwoofer’s response will begin rolling off above the frequency you set this control to. You should set the crossover frequency to obtain a smooth and seamless transition from the subwoofer to the

Краткое содержание страницы № 12

Crossovers Receiver/Processor Subwoofer Outputs The Velodyne subwoofer is designed to operate using the full range audio signal for input when using the built-in crossover. Many home theater processors/receivers (Dolby Digital™, DTS™, THX™) have a “subwoofer out” jack (sometimes labeled “LFE”) that is internally filtered, settable at the receiver/processor, and designed to be used with a powered subwoofer. In some installations, it may be beneficial to use BOTH the Velodyne crossover and the r

Краткое содержание страницы № 13

SUBWOOFER OUTPUT JACK FRONT AMPLIFIER REAR Figure 4. Line-Level Subwoofer Connection Diagram . www.v elodyne.com CHT-Q Series User’s Manual 10

Краткое содержание страницы № 14

Figure 5. Speaker-Level Subwoofer Connection Diagram . www.v elodyne.com CHT-Q Series User’s Manual 11 SUBWOOFER OUTPUT JACK REAR AMPLIFIER FRONT FRONT RIGHT SPEAKER FRONT LEFT SPEAKER

Краткое содержание страницы № 15

Interconnect Cables When installing your new Velodyne subwoofer using the line level connections, you should always use shielded phono cables. There are many high quality cables available today. It is recommended that you keep the length of cable as short as possible to avoid any potential noise problems. When using speaker level connections, use a high quality speaker cable that mates well with the connectors. Be very careful to avoid any loose strands or frayed wires that may result in a shor

Краткое содержание страницы № 16

• LIGHT — If you wish, you can deactivate the numeric LED on your CHT-Q subwoofer by pressing the LIGHT button on your remote. To reactivate the LED, press the LIGHT button again. When the display has been deactivated, it will light only when you make adjustments to the subwoofer controls and then turn off again. • NIGHT — Night mode limits the maximum dynamic output of the subwoofer for late night listening or to be more considerate of close neighbors. Press the night button to turn the night

Краткое содержание страницы № 17

The following table indicates musical style and which preset is recommended for it. MUSICAL STYLE SUGGESTED PRESET Action Adventure Movies Movies Country – Rock R&B – Rock Country – Soft Jazz – Classical Folk Jazz – Classical Indie Music R&B – Rock Pop R&B – Rock Rock R&B – Rock Alternative Rock Jazz – Classical Blues Jazz – Classical Broadway and Vocalists Jazz – Classical Children’s Music Jazz – Classical Christian and Gospel Jazz – Classical Classic Rock R&B – Rock Classical Jazz – Classica

Краткое содержание страницы № 18

Restoring Defaults There is a feature that allows you to restore default settings for your CHT-Q subwoofer. By pressing presets in EXACTLY the following order on the remote, the unit will restore its default settings. Preset 1: Movies Preset 2: R&B – Rock Preset 3: Jazz – Classical Preset 4: Games Preset 4: Games Preset 3: Jazz – Classical Preset 2: R&B – Rock Preset 1: Movies When you press the presets in the above order, the front LED will display “P3” indicating that you have restored defau

Краткое содержание страницы № 19

Troubleshooting and Service Before seeking service for your amplifier or subwoofer, please re-check all systems. Following is a simple troubleshooting guide to assist you. 1. Verify that the unit is plugged in and power outlet used is active. 2. Is the power switch on? 3. Is the unit receiving an input signal from your source? 4. Have all controls (volume, crossover, phase, etc.) been properly set? 5. If the unit has been running at high levels, one of the protection circuits may be eng

Краткое содержание страницы № 20

Specifications CHT L E D O M Q 8 — refoo W ) m 3 . 0 2 8 ) m c 5 . 0 3 ( 2 1 ) m c 8 3 ( 5 1 f o r r a w f o r r a w f o r r a w f o r r a w ) r e t e m a i d n o t s i p 3 . 6 ( ) r e t e m a i d n o t s i p 7 . 2 1 ( : r e i f i l p m A / c i m a n y D s t t a w 0 9 3 D s s a l C r e w o P S M R s t t a w 0 8 1 r e w o P S M R s t t a w 5 9 1 n g i s e D t e n i b a C n o i s r u c x E d e d n e t x E x e l f e R — s s a B d e d a o L — t o l S F r llarevO 71 z H 0 4 2 — z 0 4 6

Velodyne Acoustics
CHT-10Q Инструкция по эксплуатации

C o n g r a t u l a t i o n s !

Congratulations on your purchase of a Velodyne CHT-Q subwoofer. This system represents the

state-of-the-art in low frequency reproduction. Read and follow the instructions below to ensure

safe and proper system operation.

Note: Do not leave unit in direct sunlight or use in high humidity environments!!!

Warning!

To prevent fire or shock hazard, do not expose this product to rain or moisture. To avoid

electrical shock, do not open the speaker enclosure or amp chassis cover. Please observe all

warnings on the equipment itself. There are no user serviceable parts inside. Please refer all

service questions to your authorized Velodyne dealer.

P r i o r t o I n s t a l l a t i o n :

Please unpack the system carefully. Use caution when lifting or moving to avoid injury. Please

save the carton and all packaging materials for future use. Record the serial number in the

space provided on page 19 for future reference.

Product Features

• DSP-controlled

• Front mounted 8-segment LED display

• One-touch, 5-band graphic equalizer with microphone included

• 4 selectable presets for customized listening mode

• Night-mode setting

• Mute control

• Built-in 180 watt (RMS) power amplifier (CHT-8Q)

• Built-in 195 watt (RMS) power amplifier (CHT10Q)

• Built-in 225 watt (RMS) power amplifier (CHT-12Q)

• Built-in 750 watt (RMS) power amplifier (CHT-15Q)

• Adjustable (40 to 120 Hz) low-pass crossover with Subwoofer Direct setting

• Speaker-level inputs

• Line-level inputs

• Signal sensing auto turn on/off with bypass option

• Variable volume control with digital LED readout

• Selectable phase control (0, 90, 180, or 270 degrees)

• Dual staggered low-pass crossover; 12 dB/octave initial, 24 dB/octave ultimate

• Anti-clipping circuit

• Over excursion protection

• Slot loaded bass reflex design

.

w w w . v e l o d y n e . c o m

CHT-Q Series User’s Manual

1