Wp 10bl60 rtr инструкция на русском

User Manual of Water-Proof Brushless Speed Controller (RTR Version)

USER MANUAL

WATER-PROOF

SENSORLESS BRUSHLESS

SPEED CONTROLLER

( RTR VERSION )

【DECLARATION】

Thanks for purchasing our electronic speed controller (ESC). The power system for RC model can be very

dangerous, so please read this manual carefully. In that we have no control over the correct use,

installation, application, or maintenance of our products, no liability shall be assumed nor accepted for

any damages, losses or costs resulting from the use of the product.

【FEATURES】

1.

Water-proof and dust-proof. The ESC can work under water for a short time.

(Please remove the cooling fan when running car in water, and after running, please make the ESC

clean and then dry it to avoid the oxidation to copper connectors)

2.

Specially designed for RC car and truck, with excellent start-up, acceleration and linearity features.

3.

Drive sensorless brushless motors.

2 running modes («Forward with brake» mode, «Forward/Backward with brake» mode).

4.

5.

Proportional ABS brake function with 4 steps of maximum brake force adjustment, 8 steps of drag-brake force

adjustment.

4 start modes («Punch») from «Soft» to «Very aggressive» to be suitable for different chassis, tires and tracks.

6.

7.

Multiple protection features: Low voltage cut-off protection for Lipo or NiMH battery / Over-heat protection /

Throttle signal loss protection / Motor blocked protection.

Easily programmed with the «SET» button on the ESC or with the LED Program Card.

8.

【SPECIFICATIONS】

Model

WP-S10C-RTR

WP-S16-RTR

Cont./Burst

25A/90A

45A/260A

0.005 ohm

Resistance

0.0012 ohm

1/18,1/16 scale

Car Applicable

On-road: ≥12T

On-road: ≥9T

2S Lipo

6 cells

Off-road: ≥18T

Off-road: ≥12T

NiMH

Motor

2040 size motor

3650 size motor

On-road: ≥18T

On-road: ≥12T

Limit

3S Lipo

9 cells

Off-road: ≥24T

Off-road: ≥18T

NiMH

2040 size motor

3650 size motor

Battery

4-9 cells NiMH or 2-3S Lipo

5V*

Rating Voltage of

Without cooling

the Stock Cooling

fan

* The stock 5V cooling fan only works with 2S Lipo or 4-6 cells NiMH.

Fan (*Note 1)

When using 3S Lipo or 7-9 cells NiMH, the stock 5V cooling fan MUST

Built-in BEC

6V/1A

Program Port

Rx Wire

Dimension/Weight

36*28*21 / 38g

49*34*35/ 75g

* Note1: Please remove the cooling fan when running the ESC in water. For more information about the 12V

cooling fan, please refer to the brief

introduction on page 3.

【BEGIN TO USE THE NEW ESC】

1. Connect the ESC, motor, receiver,

battery and servo according to the

following diagram

«+» and «-» wires of the ESC are

connected with the battery pack, and #A,

#B and #C are connected with the motor

wires. The «SET» button is used for

programming the ESC.

The control cable of the ESC (trio wires

with black, red and white color) is

connected with the throttle channel of the

receiver (Usually CH2).

1The #A, #B, #C wires of the ESC can be

connected with the motor wires freely

(without any order). If the motor runs in

HW-SM601ENG-20140903 Page — 1 —

WP-S10D-RTR

WP-S10DS-RTR

WP-10BL50-RTR

WP-S10E-RTR

WP-10BL60-RTR

50A/300A

60A/390A

45A/220A

0.0010 ohm

0.0007 ohm

0.0012 ohm

1/10 scale on-road and off-road

On-road: ≥8T

On-road: ≥5.5T

On-road: ≥9T

Off-road: ≥11T

Off-road: ≥9T

Off-road: ≥12T

3650 size motor

3650 size motor

3650 size motor

On-road: ≥11T

On-road: ≥8.5T

On-road: ≥12T

Off-road: ≥14T

Off-road: ≥13T

Off-road: ≥18T

3650 size motor

3650 size motor

3650 size motor

WP-S10D-RTR: 5V*

7.4V

WP-S10DS-RTR: 5V*

7.4V

WP-10BL60-RTR:7.4V

be replaced by 7.4V or 12V cololing fan.

6V/2A

Multiplexed with cooling fan port

WP-S10D-RTR:

49*34*35 / 75g

WP-S10DS-RTR:

48.5*38*32 / 90g

48.5*38*32 /90g

49*32*41 / 75g

WP-10BL60-RTR:

48.5*38*32 / 90g

Form 1: Parameter List of QuicRun-WP16BL30 and QuicRun-WP10BL60: (Italics in the form below indicate factory defaults) Form 2: Parameter List of QuicRun-WP-8BL150 (Italics in the form below indicate factory defaults)

Option 1

1.Running Mode

2.Drag Brake Force

3. Low Voltage Cutoff

4. Start Mode (Punch)

5. Max. Brake Force

6. Max. Reverse Force

7. Initial Brake Force

8. Throttle Range

9. Timing

Option 2 Option 3 Option 4 Option 5 Option 6 Option 7 Option 8 Option 9

Fwd/Br

0%

5% 10% 20% 40% 60%

Disable

2.6V/Cell 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell

80% 100%

Fwd/Rev/Br Fwd/Rev

Level 5 Level 6 Level 7 Level 8 Level 9Level 4Level 3Level 2

Level 1

25%

50% 75% 100% Disable

25%

drag brake

force

drag brake

force

50% 75% 100%

0% 20% 40%

6%

(Narrow)

9%

(Normal)

9%

(Normal)

12%(Wide)

0.00 deg 3.75 deg 7.50 deg 11.25 deg 15.00 deg 18.75 deg 22.50 deg 26.25 deg

Enable

Disable

CCW

CW

Note 2

Auto-

identification

2S LiPo 3S LiPo 4S LiPo 5S LiPo 6S LiPo

Programmable Items

Note 1

Option 1

1.Running Mode

2.Drag Brake Force

3. Low Voltage Cutoff

4. Start Mode (Punch)

5. Max. Brake Force

6. Max. Reverse Force

7. Initial Brake Force

8. Throttle Range

9. Timing

Option 2 Option 3 Option 4 Option 5 Option 6 Option 7 Option 8 Option 9

Fwd/Br

0%

5% 10% 20% 40% 60%

Disable

2.6V/Cell 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell

80% 100%

Fwd/Rev/Br Fwd/Rev

Level 5 Level 6 Level 7 Level 8 Level 9Level 4Level 3Level 2

Level 1

25%

50% 75% 100% Disable

25%

50% 75% 100%

0% 20% 40%

6%

(Narrow)

12%(Wide)

0.00 deg 3.75 deg 7.50 deg 11.25 deg 15.00 deg 18.75 deg 22.50 deg 26.25 deg

10. Overheat

Protection

11. Motor Rotation

12.Cell Count

Programmable Items

Note 1

Note 1: Fwd=Forward, Rev=Reverse, Brk=Brake

Note 2: When set to the “Auto-identification” mode, the battery pack can only be identified as 2S, 4S and 6S Lipo. Because the

normal voltage of each LiPo cell varies from 2.6V to 4.2V, it’s not easy to correctly calculate the cell count of a discharged LiPo

battery pack. Therefore, we strongly suggest you set the “LiPo Cells” manually.

In order to make sure the ESC fits the throttle range of your transmitter, you must calibrate it when begin to use a new ESC, or a used transmitter if some of its settings have been changed,

like the Throttle Trim, D/R, EPA or other parameters. Otherwise, the ESC cannot work properly. Besides, we strongly recommend users to enable the “failsafe” function of the transmitter, set

the “F/S” of the throttle channel to the Shutdown mode or set the protection value to the neutral position, so the car can be stopped if the receiver fails to get the radio signals from the

transmitter. Please calibrate the throttle range according to the following steps.Model QuicRun-WP-16BL30 QuicRun-WP-10BL60Continuous Current /Peak Current / ResistanceMotor Type SupportedCar Applicable30A/180A/0.002Ω

Sensorless Brushless Motor (compatible with sensored motor but not in sensored operating mode）

1:18 & 1:16 On-road / Off-road / Buggy / Monster 1:10 On-road / Off-road / Buggy / Monster

60A/360A/0.001Ω6V/3A (Switch Mode)Motor LimitBattery 4-9 Cells NiMH, 2-3S Lipo 4-9 Cells NiMH, 2-3S LipoQuicRun-WP-8BL1501:8 Buggy / Monster150A/950A/0.00035Ω6V/3A (Switch Mode)9-18 Cells NiMH, 3-6S LipoBEC OutputDimensions / WeightExternal Program PortWorking voltage of Fan36x28x16mm / 38gNot AvailableNo cooling fan48.5x38x32mm / 90gAvailableFrom BEC(6V)59.5x48x42mm / 178gAvailableFrom BEC(6V)6V/1A (Linear Mode)For 2S Lipo or 6 cells NiMH:1. On-road: 2435-size or smaller motor with the KV<80002. Off-road / Buggy / Monster: 2435-size or smaller motor with the KV<5000For 3S Lipo or 9 cells NiMH:1. On-road: 2435-size or smaller motor with the KV<55002. Off-road / Buggy / Monster: 2435-size or smaller motor with the KV<3500.For 2S Lipo or 6 cells NiMH:1. On-road: 3656-size or smaller motor with the KV<60002. Off-road / Buggy / Monster: 3656-size or smaller motor with the KV<4000For 3S Lipo or 9 cells NiMH:1. On-road: 3656-size or smaller motor with the KV<40002. Off-road / Buggy / Monster: 3656-size or smaller motor with the KV<3000.For 4S Lipo or 12 cells NiMH:4274-size or smaller motor with the KV<3000For 6S Lipo or 18 cells NiMH:4274-size or smaller motor with the KV<2400

• Water-proof and dust-proof for all-weather races;

(Note: please uninstall the cooling fan before using this ESC in water; Clean and dry it soon after the

use for avoiding the connectors get rusty.)

• External programming port, easy to connect to the Program Card when setting the ESC;

• Proportional brake with 4 steps of maximum brake force adjustment and 8 steps of drag brake force adjustment;

• 9 steps of acceleration(punch) adjustment from “soft” to “Very aggressive” to fit for different kinds

of models, tires and tracks;

• Multiple protections: Low voltage cut-off protection / Over-heat protection / Throttle signal loss

protection / Motor lock-up protection;

• One-button(the “SET” button on the ESC) to set the ESC, and easy to reset all parameters to the

factory default settings;

• Compatible with the optional device-the portable Digital LED Program Card, especially convenient

for outdoor use.

01

Features

02

Begin to Use a New Brushless ESC

03

Program the ESC

Connections

Specifications

IMPORTANT

CAUTIONS

ATTENTION

Congratulations and thanks for purchasing HOBBYWING electronic speed controller (ESC). The brushless power system for RC model can be very powerful and dangerous, so please read this manual carefully. Since we have no control over the installation, application, use or maintenance of this product, in no case shall we be liable for any damages, losses or costs. Besides, we have the rights to change the design, appearance, functions and operational requirements without any notifications.

ATTENTION

1

Program the ESC with the SET Button

1

Set the ESC by the Program Card

2

Set up Throttle Range

2

• In the programming process, the motor will emit “Beep” tone while the LED is

flashing.

• If the “N” is bigger than the number “5”, we use a long time flash and long

“Beep—” tone to represent “5”, so it is easy to identify the items of the big number.For example, if the LED flashes as the following:“A long time flash + 1 short time flash” (Motor sounds “B—B”) = the No. 6 item“A long time flash + 2 short time flash” (Motor sounds “B—BB”) = the No. 7 item“A long time flash + 3 short time flash” (Motor sounds “B—BBB”) = the No. 8 item, and so on.The Program Card is optional equipment which needs to be purchased separately. It has 3 digital LEDs to display the programmable items’ number and the options’ number. (Please refer to the user manual of the program card for detail info)

ATTENTION

The QuicRun-WP10BL60 and QuicRun-WP8BL150 can only be connected to the program card via the external programming port.

ATTENTION

a) When the throttle stick is in the neutral range, neither the Red LED nor the Green LED lights up;

b) When the car moves forward, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the top position (100% throttle);

c) When the car brakes, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the bottom position and the maximum brake force is set to 100%;

d) When the car reverses, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the bottom position and the maximum reverse force is set to 100%.

Check the LED Status in Normal Running

3

Explanation for the Beep Sound

In normal case, when the ESC is switched on, the motor will emit several “Beep” tones to express the cell count of the battery pack. For example, “Beep-Beep-” means 2S LiPo,

“Beep-Beep-Beep-” means 3S LiPo, “Beep-Beep-Beep- Beep-” means 4S LiPo.

EXPLANATION

06

Trouble Shooting

Trouble(s) Solution(s)Possible Causes

No battery voltage is input to the ESC. The switch of the ESC is damagedThe voltage of the battery pack is not in the normal range, it’s too high or too low. The throttle signal wire is oppositely inserted or into the incorrect channel. The wire connections between the ESC and the motor need to be changed.Low voltage cutoff protection (Red LED blinks) Overheat protection (Green LED blinks)The throttle neutral point drifts to the brake area. The connections between motor and ESC are not reliable. The ESC is damaged.Check the connections between the battery and the ESC, re-solder the connectors if needed. Change the switch.Check the voltage of the battery pack.

Plug the signal wire (Rx lead) correctly into the throttle channel (usually Channel #2) of the receiver.

Swap any two wire connections between the ESC and the motor. Check the battery voltage. If still has some capacity, lower the cut-off threshold voltage; if not, replace a new battery.

Wait several minutes to cool the ESC. Increase the gear ratio or the T number (Turns) of the motor.

Calibrate the throttle neutral point again to ensure that no LED lights when the throttle stick is at the neutral position. Check all the solder joints and ensure they are well soldered. Check connectors.Contact the distributor for after-sales service. After power on, motor doesn’t work but emits “beep-beep-, beep-beep-”alert tone. (there’s 1 second pause between 2 “beep-beep-”).After power on, the Red LED turns solid red but the motor doesn’t work.

Turn on the switch, no LED lights up, and neither the motor nor fan works.

The car runs backwards when accelerating forward on radio.The motor stutters, and cannot start up.The vehicle can go forward but cannot reverse.The car suddenly slows down, then stops about 15 seconds later.Enter the 2

nd

item»Drag Brake Force»Hold the SET keySwitch on the ESCRed LED flashes Green LED flashesonce Green LED flashestwiceGreen LED flashes3 times Green LED flashesN times ReleaseSET kyeReleaseSET kyePressSET kyePressSET kyePressSET kyePressSET kyeReleaseSET kyeReleaseSET kyeRed LED flashes once, choose «0%» Red LED flashes twice, choose «5%»Red LED flashes 3 times, choose «10%» Red LED flashes 4 times, choose «20%» Red LED flashes 5 times, choose «40%»Red LED flashes 6 times, choose «60%» Red LED flashes 7 times, choose «80%»Red LED flashes 8 times, choose «100%» Red LED flashes once, choose «None»Red LED flashes twice, choose «2.6V»Red LED flashes 3 times, choose «2.8V»Red LED flashes 4 times, choose «3.0V»Red LED flashes 5 times, choose «3.2V»Red LED flashes 6 times, choose «3.4V»Red LED flashes once to choose Red LED flashes twice to choose Red LED flashes 3 times to choose «Forward with brake»»Forward / Reverse with brake»»Forward / Reverse»Enter the 3

rd

item»Low Voltage Cut-Off»Enter the N

th

itemEnter the 1

st

item»Running Mode»Turn off the ESCTurn on the transmitterHold SET key for 3 secondsHold SET key for 3 secondsHold SET key for 3 secondsHold SET key for 3 seconds……The following steps are just like the above setps……Finish programming, switch off the ESC, and then switch it on

05

Programmable Items

1. Running Mode: With “Forward with Brake” mode, the car can go forward and brake, but cannot go backward, this mode is suitable for competition; “Forward / Reverse with Brake” mode provides backward function, which is suitable for daily training.

Note: “Forward/Reverse with Brake” mode uses “Double-click” method to make the car go backward. When you move the throttle stick from forward zone to backward zone for the first time (The 1st “click”), the ESC begins to brake the motor,

the motor speeds down but it is still running, not completely stopped, so the backward action is NOT happened immediately. When the throttle stick is moved to the backward zone again (The 2nd “click”), if the motor speed is slowed down to

zero, then the backward action will happen. The “Double-Click” method can prevent mistakenly reversing action when the brake function is frequently used in steering. By the way, in the process of braking or reversing, if the throttle stick is

moved to forward zone, the motor will run forward at once. “Forward/Reverse” mode uses “single-click” method to make the car reverse. When moving the throttle stick from neutral zone to backward zone, the vehicle reverses immediately,

so this mode is usually used in rock crawling.

2. Drag Brake Force: Set the amount of drag brake applied at neutral throttle to simulate the slight braking effect of a neutral brushed motor while coasting.

3. Low Voltage Cut-Off: The function mainly prevents the Lipo battery from over discharging. The ESC detects the battery voltage at any time, if the voltage is lower than the threshold for 2 seconds, the output power will be reduced 70%,

after 15 seconds the output power will be completely shut off and the red LED flashes in such a way: “☆-, ☆-, ☆-”. Please stop your car at the track side as soon as possible to avoid obstructing other racing cars.

Note: For NiMH battery, if the voltage of the whole NiMH battery pack is higher than 9.0V, it will be considered as a 3 cells Lipo battery pack; If it is lower than 9.0V, it will be considered as a 2 cells Lipo battery pack. For example, if a NiMH battery

pack is 8.0V, and the threshold is set to 2.6V/Cell, so it will be considered as a 2 cells Lipo battery pack, and the low-voltage cut-off threshold for this NiMH battery pack is 2.6×2=5.2V.

4. Start Mode (Also called “Punch” or “Acceleration”): Level 1 has very soft start acceleration, while level 9 has very quick start acceleration. From Level 1 to Level 9, the start force is increasing. If you choose “Level 7” to “Level 9”, you should use good

quality battery with powerful discharge ability, otherwise you cannot get the burst start effect as you want. If the motor cannot run smoothly (the motor is cogging), sometimes it is caused by the weak discharge ability, please use a better

battery or increase the gear ratio.

5. Maximum Brake Force: The ESC provides proportional brake function. The brake force is related to the position of the throttle stick. Maximum brake force refers to the force when the throttle stick is located at the top point of the backward

zone. A very large brake force can shorten the brake time, but it may damage the gears.6. Maximum Reverse Force: Sets how much power will be applied in the reverse direction.

7. Initial Brake Force: It is also called “minimum brake force”, which refers to the force when the throttle stick is located at the initial position of the backward zone. The default value is equal to the drag brake force, so the brake action can be very smoothly.

8. Throttle Neutral Range: This setting adjusts the width of the neutral range.

9. Timing: This function can be used to fine-tune the output power of the motor, the bigger the timing, the faster the motor runs or the larger output power of the motor. As the Boost Timing technology has been introduced into this ESC, so

under the sensored mode, adjust the ESC timing can greatly increase the motor RPM. Therefore, please remember to enlarge the gear ratio of the chassis and carefully check temperatures of the motor and the ESC after increasing the timing.

10. Over-Heat Protection: If this function is activated, the output power will be cut off when the temperature is higher than the factory-preset value for 5 seconds. When the protection happens, the Green LED will flash in such a way “☆-, ☆-, ☆-” .

11. Motor Rotation: Face to the motor shaft (that means the endbell of the motor is far from your face), and move the throttle stick to forward zone. If this programmable item is set to “CCW”, the shaft runs counter-clockwise; if it is set to “CW”, the

shaft runs clockwise.

12. Cell Count: We strongly suggest you set the “Cell Count” manually instead of using the “Auto-identification” mode.

04

Reset All Items to Default Values

At any time when the throttle is located in neutral zone (except in the throttle calibration or parameters program process), press and hold the “SET” key for over 3 seconds, the red LED and green LED will flash

simultaneously , which means each programmable item has be reset to its default value. The ESC needs to be restarted to complete the reset process.

Click the SET button to choose the option, the times the red LED blinks indicates the option number you are going to select. After entering the corresponding item, the red LED starts to blink, the times it blinks represents the current option number.Press SET key to choose the value, the flash times of the RED LED means the option number.(Once means the 1st option, twice means the 2nd option, etc.)

USER MANUAL

16BL30 • 10BL60 • 8BL150Brushless Electronic Speed ControllerThis brushless system is powerful and dangerous, for the safety of your own and those people around you, please turn on the ESC while keeping all the wheels in the air.

1. Turn on the transmitter, and set parameters (of the throttle channel) like “D/R, “EPA”, “ATL” to 100% (if there is no LCD display

on the transmitter, please adjust the corresponding knob to its limit). Set the throttle trim to 0 (if there is no display, then adjust the

knob to the neutral position). For FUTABA

TM

and similar transmitters, set the throttle direction to “REV”, while the throttle direction

of others to “NOR”. Please disable the built-in ABS brake function in your transmitter.

2. Hold the SET button while sliding the switch to the ON position, and then release the “SET” button the moment when the Red

LED starts to blink. (If you don’t release the SET button in 3 seconds, the ESC will enter the program mode, in such a case, please

switch off the ESC and re-calibrate the throttle range again from Step 1.)

Hold down the set button.

Move the throttle stick to the neutral position and press

the set button.

Turn on the switchRelease the set button once the LED flashes.

Set the 3 points according to pictures

• The neutral point. • The end point of the forward direction. • The end point of the backward/brake direction.

When the process of calibration is finished, the motor can be started after 3 seconds.

The Green LED

flashes once and

motor emits

“Beep” tone.

Move the throttle stick to the end position of forward

and press the set button.

The Green LED flashes

twice and motor emits

“Beep-Beep”

tone.

Move the throttle stick to the end position of forward

and press the setup button.

The Green LED flashes

twice and motor emits

“Beep-Beep-

Beep” tone.

BatteryMotor

Blue

YellowOrangeReceiverSwitchElectronic Speed Controller

External Programming

Port for Connecting

Program Card.

User Manual of Water-Proof Brushless Speed Controller (RTR Version)

the opposite direction, please swap any two wire connections.

Note: You can use the transmitter to set the throttle channel to the»Reverse» direction, and then the motor

will run oppositely. Please calibrate the throttle range again after changing the direction of throttle

channel.

2. Throttle Range Setting (Throttle Range Calibration)

In order to make the ESC match the throttle range, you must calibrate it when you begin to use a new ESC, or a

new transmitter, or after changing the settings of the neutral position of throttle channel, ATV or EPA parameters,

otherwise the ESC cannot work properly.

There are 3 points need to be set, they are the top point of «forward»,» backward» and the neutral point.

The following pictures show how to set the throttle range with a Futaba

A) Switch off the ESC, turn on the

transmitter, set the direction of throttle

channel to «REV», set the «EPA/ATV»

value of throttle channel to «100%», and

disable the «ABS» brake function of

your transmitter.

(*Note2)

B) Hold the «SET» key and then switch on

the ESC, when the red LED begins to

flash, release the key immediately.

(Please check the picture on the right side)

C) Set the THREE points according to the

steps shown in the picture on the right

side.

1) Neutral point

2) End point of forward direction

3) End point of backward direction

D) When the process of calibration is

finished, the motor can be started after

3 seconds.

Note2: If you don’t release the «SET» key after the

red LED begins to flash, the ESC will enter the

program mode, in such a case, please switch off

the ESC and re-calibrate the throttle range again

from step A to step D.

3. The LED Status in Normal Running

a)

When the throttle stick is in the neutral range, neither the Red LED nor the Green LED lights up.

b)

When the car moves forward, the Red LED solidly lights; the Green LED also lights up when the throttle stick is

at the top position (100% throttle).

c)

When the car brakes, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the

bottom position and the maximum brake force is set to 100%.

d)

When the car reverses, the Red LED solidly lights.

【ALERT TONES】

1.

Input voltage abnormal alert tone: The ESC begins to check the input voltage when power on, if it is out of the

normal range, such an alert tone will be emitted: «beep-beep-, beep-beep-, beep-beep-» (There is 1 second

time interval between every «beep-beep-» tone).

2.

Throttle signal abnormal alert tone: When the ESC can’t detect the normal throttle signal, such an alert tone

will be emitted: «beep-, beep-, beep-» (There is 2 seconds time interval between every «beep-» tone).

【PROTECTION FUNCTION】

1.

Low voltage cut-off protection: If the voltage of a Lipo battery pack is lower than the threshold for 2 seconds,

the ESC will cut off the output power. Please note that the ESC cannot be restarted if the voltage of each Lipo

cell is lower than 3.5V.

For NiMH battery packs, if the voltage of the whole NiMH battery pack is higher than 9.0V but lower than 12V,

it will be considered as a 3S Lipo; If it is lower than 9.0V, it will be considered as a 2S Lipo. For example, if the

NiMH battery pack is 8.0V, and the threshold is set to 2.6V/Cell, it is considered as a 2S Lipo, and the

low-voltage cut-off threshold for this NiMH battery pack is 2.6*2=5.2V.

TM

transmitter.

2.

Over-heat protection: When the temperature of the ESC is over a factory preset threshold for 5 seconds, the

ESC will cut off the output power. You can disable the over-heat protection function for competition race.

3.

Throttle signal loss protection: The ESC will cut off the output power if the throttle signal is lost for 0.2 second.

【PROGRAM THE ESC】

1. Program Method

Note:

In the program process, the motor will emit «Beep» tone when the LED is flashing.



th

programmable item is represented by 5 short Beeps (that is, «BBBBB»).



The 5

For the options of each programmable item, we use a long time flash and long «Beep—» tone to represent



number «5», so it is easy to identify the options with big numbers.

For example, if the LED flashes as the following:

«A long time flash» (Motor sounds «B—«) = The option 5

«A long time flash + a short time flash» (Motor sounds «B—B») = The option 6

«A long time flash + 2 short times flash» (Motor sounds «B—BB») = The option 7

«A long time flash + 3 short times flash» (Motor sounds «B—BBB») = The option 8

HW-SM601ENG-20140903 Page — 2 —